Injection molding process is the most important factor affecting product appearance and performance. Why do you say that? Because plastic product performance and appearance are good and bad decision of injection molding, good injection molding technology can even use a little material to make and raw material products about the same appearance and performance. First of all, the injection molding process is divided into two stages: material melting and injection molding. The melting stage is mainly to use the machine's own hot melt system to change the material from solid to injection flow state. In this process for temperature regulation is very important, the level of temperature determines the air content and water vapor content of the melted material, directly affect the appearance of the product after injection molding. Secondly, in the process of injection molding material reserve time is also very key, too long time will cause low production efficiency, and too short will cause the product can not take shape. So in the calculation of time to do scientific rigor. Finally is the injection molding equipment adjustment. For the new injection molding machine is able to adjust the automatic state, the advantage of automatic mode is that there is not too much manpower to manage and observe the production of equipment, saving manpower.
1, Cable Lugs are suitable for the connection of copper conductors in power cable with electronic equipmentCORD-END TWIN Terminals | |||||||||||||||
WIRE RANGE | DIMENSIONS(mm) | COLOR SYSTEM | |||||||||||||
PART NO | ITEM NO | D1 | Tolerance | D2 | Tolerance | L | Tolerance | L1 | Tolerance | S1 | S2 | DIN | W | T | |
LY016-5-01 | CT205008 | 2×0.50 | 1.50 | ±0.14 | 2.5/4.7 | +/-0.2 | 15.0 | ±1.5 | 8.0 | ±0.5 | 0.15 | 0.25 | WHITE | ORANGE | WHITE |
LY016-5-02 | CT207508 | 2×0.75 | 1.80 | ±0.14 | 2.8/5.0 | +/-0.2 | 15.0 | ±1.5 | 8.0 | ±0.5 | GREY | WHITE | Blue | ||
CT207510 | 2×0.75 | 1.80 | 2.8/5.0 | 17.0 | 10.0 | ||||||||||
LY016-5-03 | CT210008 | 2×1.00 | 2.05 | ±0.25 | 3.4/5.4 | +/-0.2 | 15.0 | ±1.5 | 8.0 | ±0.5 | 0.30 | RED | YELLOW | RED | |
CT210010 | 2×1.00 | 2.05 | 3.4/5.4 | 17.0 | 10.0 | ||||||||||
LY016-5-04 | CT215008 | 2×1.50 | 2.30 | ±0.25 | 3.6/6.6 | +/-0.2 | 16.0 | ±1.5 | 8.0 | ±0.5 | BLACK | RED | BLACK | ||
CT215012 | 2×1.50 | 2.30 | 3.6/6.6 | 20.0 | 12.0 | ||||||||||
LY016-5-05 | CT225010 | 2×2.50 | 2.80 | ±0.25 | 4.2/7.8 | +/-0.2 | 18.5 | ±1.5 | 10.0 | ±0.8 | 0.20 | 0.40 | BLUE | BLUE | GREY |
CT225013 | 2×2.50 | 2.80 | 4.2/7.8 | 21.5 | 13.0 | ||||||||||
LY016-5-06 | CT240012 | 2×4.00 | 3.70 | ±0.3 | 4.9/8.8 | +/-0.4 | 23.0 | ±1.5 | 12.0 | ±0.8 | GREY | GREY | ORANGE | ||
CT260014 | 2×6.00 | 4.80 | ±0.3 | 6.9/10.0 | +/-0.4 | 26.0 | ±1.5 | 14.0 | ±0.8 | YELLOW | BLACK | ||||
LY016-5-07 | CT2100014 | 2×10.00 | 6.40 | ±0.3 | 7.6/12.8 | +/-0.4 | 26.5 | ±1.5 | 14.0 | ±0.8 | 0.50 | RED | IVORY | BROWN | |
LY016-5-08 | CT2160014 | 2×16.00 | 8.30 | ±0.3 | 9.6/18.6 | +/-0.4 | 31.5 | ±1.5 | 14.0 | ±0.8 | 0.30 | BLUE | GREEN | IVORY |
Product Categories : Copper Connecting Terminals
Terminal Copper Bimetallic Cable Lug Longyi Terminals
Terminal Pin Full Range Wire Connector Terminals
Electrical Crimp Fork Terminal Connector Cable Lug
Type Tinned Copper Cable Lug for Cable Connection
Insulated Copper Terminal Connector Terminals
Longyi Circular Nylon Terminal Ring Nylon Terminal
Copper Lug Electric Tube Pre-Insulated
Connectors Copper Cable Lug for Cable Connection